UNS S30100 Sheets, SS 301 Plates, AISI SS 301 Stainless Steel 301 Sheets Supplier, Manufacturer and Exporter in India
Din 1.4310 SS 301 Plates, SS UNS S30100 Sheets, Stainless Steel 301 Plates, 301 Stainless Steel 301 Sheets Suppliers in India.
STAINLESS STEEL 301 SHEETS AND PLATES GENERAL PROPERTIES:
Stainless steel grade 301 is a commonly available austenitic stainless with good corrosion resistance and elevated carbon to allow for cold working to a variety of tempers. It can be obtained in the 1/4 hard, 1/2 hard, and full hard.
STAINLESS STEEL 301 SHEETS AND PLATES APPLICATIONS:
High strength and excellent corrosion resistance make Type 301 Stainless Steel useful for a wide variety of applications. Typical uses include:
- aircraft structural parts
- trailer bodies
- utensils
- architectural and automotive rim
- roof drainage products
- conveyor belts
- variety of industrial applications.
STAINLESS STEEL 301 SHEETS AND PLATES CORROSION RESISTANCE:
- Good resistance in applications involving external exposure to mildly corrosive conditions at ambient temperatures.
- Resists outdoor, industrial, marine, and mild chemical environments
- susceptible to carbide precipitation during welding, which restricts its use in some applications
- Similar to resistance of Stainless Steel grade 304
STAINLESS STEEL 301 SHEETS AND PLATES HEAT RESISTANCE:
- Can be exposed continuously without appreciable scaling to a max of 1600°F(871°C).
- Maximum exposure temperature is about 1450°F (788°C), for intermittent exposure
- Has an oxidation weight gain of 10mg/cm 2 in 1,000 hours, in temperatures over 1600°F (871°C).
STAINLESS STEEL 301 SHEETS AND PLATES HEAT TREATMENT:
- Solution Treatment (Annealing) – Heat to 1010-1120°C and cool rapidly.
- Use low side of range for intermediate annealing.
- This grade cannot be hardened by thermal treatment.
STAINLESS STEEL 301 SHEETS AND PLATES COLD WORKING:
- hardens at high rate, creating a very high strength from cold rolling and from roll forming.
- more difficult to work than other austenitic stainless steels, due to its high work hardening rate..
- strain-hardened austenitite steel undergoes partial transformation into martensitite steel during this process.
- severe cold deformation can still occur, due to residual ductility.
- Grade 301 becomes strongly magnetic when cold rolled.
STAINLESS STEEL 301 SHEETS AND PLATES WELDING:
- must be annealed for maximum corrosion resistance
- more difficult to work than other austenitic stainless steels, due to its high work hardening rate..
- must be annealed for maximum corrosion resistance
- Welding and post weld annealing will both remove high strength induced by prior cold rolling.
- Spot welding is commonly used to assemble cold rolled 301 components..
- material will lose temper in the heat affected weld zone.
STAINLESS STEEL 301 SHEETS AND PLATES CHEMICAL PROPERTIES:
| % | Cr | Ni | C | Si | Mn | P | S | N | |
|---|---|---|---|---|---|---|---|---|---|
| 301 | Min: | 16 | 6 | - | - | - | - | - |
- |
| Max: | 18 | 8 | 0.15 | 1.00 | 2.0 | 0.045 | 0.030 | 0.10 |
STAINLESS STEEL 301 SHEETS AND PLATES MECHANICAL PROPERTIES:
| Grade/Temper | Tensile Strength ksi (min.) | Yield Strength 0.2% ksi (min.) | Elongation -% in 50 mm (min.) |
|---|---|---|---|
| 301 1/4 | 125 | 75 | 25 |
| 301 1/2 | 150 | 110 | 18 |
| 301 Full Hard | 185 | 140 | 9 |
STAINLESS STEEL 301 SHEETS AND PLATES PHYSICAL PROPERTIES:
| Denstiy lbm/in3 | Coefficient of Thermal Expansion (min/in)-°F | Electrical Resistivity mW-in | Thermal Conductivity BTU/hr-ft-°F | Melting Range | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| 0.29 | at 68 – 212°F | at 68 – 932°F | at 68 – 1450°F | at 68°F | at 212°F | at 392°F | at 752°F | at 1112°F | at 1472°F | at 68 – 212°F | 2550-2590°F |
| 9.2 | 10.4 | 10.9 | 28.3 | 30.7 | 33.8 | 39.4 | 43.7 | 47.6 | 9.4 | ||
| STAINLESS STEEL 301 SHEETS AND PLATES,GRADES WITH THICKNESS AND WIDTH | |
|---|---|
| Thickness Range of Stainless Plate | 3/16″ Thru 6″ Thick Stainless Steel Plate |
| Common Widths of Stainless Plate Coil | 48″ Wide – 60″ Wide – 72″ Wide – 78.75″ (2 Meter) wide – 84″ wide – 96″ wide – 120″ wide & other widths upon customer request. |
| 200-300 Series Stainless Steel Grades | 202- 301 – 304 – 304L – 304L Polished – 304H – 309 – 309S – 309H – 310 – 310S – 310H – 316L – 316L Polished – 317L – 317LMN – 321 – 321H – 330 – 347 347H |
| 400 Series Stainless Steel Grades | 405 – 410 – 410S – 416 – 420 – 440C |
| Duplex Stainless Steel Grades | LDX 2101 – Duplex 2205 – Duplex 2507 |
| Precipitation Hardening Grades | 17-4PH – 17-4 H1150 (per customer request) – 15-5PH |
| Nickel Alloy Grades | Alloy 20 – Alloy 200 – Alloy 400 – Alloy 600 – Alloy 800 – Alloy 800HT – Alloy C-276 (nickel grades may require lead time) |
We export our STAINLESS STEEL 301 SHEETS AND PLATES products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at harshsteel@ymail.com for your instant requirements.
