Stainless Steel 420 Fittings, UNS S42000 Fittings Supplier & Exporter

GENERAL PROPERTIES:-

Alloy 420 is a hardenable, martensitic stainless steel that is a modification of Alloy 410. Similar to 410, it contains a minimum of 12% chromium, just sufficient enough to give corrosion resistant properties. Alloy 420 has higher carbon content than Alloy 410 which is designed to optimize strength and hardness characteristics. It has good ductility it the annealed condition but is capable of being hardened up to Rockwell hardness 50 HRC, the highest hardness of the 12% chromium grades. Due to its hardening properties, Alloy 420 is not often welded, although it is possible. Martensitic stainless steels are designed for high hardness and sometimes other properties are to some degree compromised. Corrosion resistance is lower than the common austenitic grades and their useful operating range is limited by their loss of ductility at sub-zero temperatures and loss of strength by over-tempering at elevated temperatures. Its best corrosion resistance is achieved when the metal is hardened and surface ground or polished.

APPLICATIONS:-

Alloy 420 is used for a variety of applications where good corrosion and outstanding hardness is necessary. It is not usually used at temperatures exceeding 800oF (427oC) due to quick hardening and loss of corrosion resistance. Examples of applications that use alloy 420 include:

• Cuttery
• Knife blades
• Surgical instruments
• Needle valves
• Shear blades
• Scissors
• Hand tools

CORROSION RESISTANCE:

• Less resistant than the austenitic grades and the 17% chromium ferritic alloys
• Good resistance in the hardened condition to the atmosphere, foods, fresh water, and mild acids
• Resistance lowered in the annealed condition
• Best with a smooth surface finish

HEAT RESISTANCE:

• Not recommended for use above the relevant tempering temperature because of reduction in mechanical properties
• Scaling temperature is approximately 1202oF (650oC)

WELDING:

• Not commonly welded due to air hardening characteristics.
• Welding may be performed after preheating to 300-400 F
• Post weld tempering at temperature for 2 hours

HOT WORKING:

• Recommended to bring temperatures slowly up to 1400, then on to 2000-2200 F
• Furnace cool slowly to avoid cracking, after furnace working
• Reheating is necessary to keep working temperature above 1600 F.

COLD WORKING:

• Can withstand only minor cold work.
• Radical forming operations will result in cracking.

ANEALING:

• Anneal at temperatures between 1550-1650 F (843-900 C)
• Allow for slow furnace cooling.

TEMPERING:

• Temper at temperatures of 300-400 F
• Air cool for maximum hardness and corrosion resistance.

HARDENING:

• Soak at 1850-1950 F to quench in heated oil.

CHEMICAL PROPERTIES:-

MECHANICAL PROPERTIES:

PHYSICAL PROPERTIES:

Fittings and Flanges for Stainless Steel Pipe
Stainless steel piping systems can be joined by butt welding and, in the heavier 40S and 80S schedules, with threaded connections.

BUTT WELDING STAINLESS STEEL PIPE FITTINGS

Harsh steel stocks butt welding fittings in the following configuration.

• Elbows 45 degree and 90 degree - long radius and short radius.
• Return bends 180 - long radius and short radius.
• educers - concentric and eccentric.
• Tees - equal and reducing.
• Caps.
• Stub ends - Type B.

Advantages of stainless steel butt Weld fitting to the pipe are to keep pipes permanently leak proof. The continuous structure helps strength between pipes and fittings. It reduces pressure and also minimises the action of corrosion and erosion. Butt welding fittings can be supplied in either seamless or welded construction and are covered by specifications ASTM A403M and ASTM A815M for Duplex grades.

STAINLESS STEEL SCREWED AND SOCKET WELD FITTINGs

Stainless steel piping systems can be connected using stainless steel screwed fittings - BSP threaded ("150lb") low pressure stainless steel fittings and NPT class 3000 high pressure stainless fittings in Grade 316. Socket weld fittings are used in high pressure piping systems and available in grade 316L to suit schedule 80S wall thickness piping.

MANUFACTURING SPECIFICATIONS:

• ASTM A182M (3000lb NPT and socket weld).
• ANSI B16.3 (BSP dimensions)
• ISO 4144 (BSP dimensions)

STAINLESS STEELS FITTINGS AND FLANGES:

A flange is a ring of steel (forged, cut from plate, or rolled) designed to connect sections of pipe, or to join pipe to a pressure vessel, valve, pump or other integral flanged assembly. Flanges are joined to each other by bolts, and to the piping system by welding or threading (or loose when stub ends are used). Forged stainless steel flanges are designed to the following common pressure ratings, stainless steel flanges are exported by Harsh Steel in Classes 150, 300, 600, 900, 1500 and 2500. Standard sealing face is Raised Face (RF).
The basic types of flanges are:

• Stainless steel slip-on flange
• Stainless steel socket weld flange
• Stainless steel blind flange
• Stainless steel lap joint flange
• Stainless steel weld neck flange
• Stainless steel threaded flange
• Stainless steel orifice Flange

Manufacturing specification: ASTM A182M
Plate stainless steel flanges are cut and machined from plate - Table 'D', Table 'E', etc.
Manufacturing specification: AS2129.
Types and applications of Stainless steel and Nickel alloy flanges

Enquiry