UNS S31653 Square Tubes, SS 316LN Square Tubes, AISI SS 316LN Stainless Steel 316LN Square Tubes Supplier, Manufacturer and Exporter in India
Din 1.4429 SS 316LN Square Tubes, SS UNS S31653 Square Tubes, Stainless Steel 316LN Square Tubes, 316LN Stainless Steel 316LN Square Tubes Suppliers in India.
STAINLESS STEEL 316LN SQUARE TUBES INTRODUCTION:
Stainless steel grade 316LN is an austenitic type of steel that is a low carbon, nitrogen-enhanced version of grade 316 steel. The nitrogen content in this steel provides solid solution hardening, and raises its minimum specified yield strength. It also possesses good resistance to general corrosion and pitting/crevice corrosion.
The following datasheet provides an overview of stainless steel grade 316LN.
STAINLESS STEEL 316LN SQUARE TUBES CHEMICAL COMPOSITION:
The chemical composition of grade 316LN stainless steel is outlined in the following table.
| Element | Content (%) |
|---|---|
| Iron, Fe | Balance |
| Chromium, Cr | 16.0-18.0 |
| Nickel, Ni | 10.0-14.0 |
| Molybdenum, Mo | 2.0-3.0 |
| Manganese, Mn | 2.00 |
| Silicon, Si | 1.00 |
| Nitrogen, N | 0.10-0.30 |
| Phosphorous, P | 0.045 |
| Carbon, C | 0.03 |
| Sulphur, S | 0.03 |
STAINLESS STEEL 316LN SQUARE TUBES MECHANICAL PROPERTIES:
The mechanical properties of grade 316LN stainless steel are displayed in the following table.
| Properties | Metric | Imperial |
|---|---|---|
| Tensile strength | 515 MPa | 74694 psi |
| Yield strength | 205 MPa | 29732 psi |
| Modulus of elasticity | 190-210 GPa | 27557-30457 ksi |
| Poisson's ratio | 0.27-0.30 | 0.27-0.30 |
| Elongation at break (in 50 mm) | 60% | 60% |
STAINLESS STEEL 316LN SQUARE TUBES OTHER DESIGNATION:
Equivalent materials to grade 316LN stainless steel are given below.
| ASTM A182 | ASTM A213 | ASTM A240 | ASTM A240 | ASTM A276 |
| ASTM A193 (B8MN, B8MNA) | ASTM A312 | ASTM A336 | ASTM A358 | ASTM A376 |
| ASTM A194 (B8MN, B8MNA) | ASTM A403 | ASTM A430 | ASTM A479 | ASTM A666 |
|
ASTM A688 |
ASTM A813 |
ASTM A814 |
DIN 1.4406 |
DIN 1.4429 |
STAINLESS STEEL 316LN SQUARE TUBES APPLICATION:
Grade 316LN stainless steel is widely used in the following applications:
- Trauma nails
- Orthopedic implants
- Neurological applications
- Surgical instruments
STAINLESS STEEL 316LN SQUARE TUBES PRODUCT OVERVIEW:
| Stainless Steel Square Tube | |
|---|---|
| Thickness Range of Stainless Plate | 3/16″ THRU 4″ (LARGER SIZES AVAILABLE UPON REQUEST) |
| Grades | 202, 304/304L, 316/316L,304H, 316H, 309/S, 310/S, 317/L, 321/H, 347/H, 904L, 330, 254SMO, 410. In duplex grades, we can supply 2205 and 2507. Some nickel Alloy such as alloy 200/201, C276, Alloy 400, Alloy 600, Alloy 625, Alloy 800H, Alloy 800HT, 254SMO, AL6XN and others Titanium alloys and copper alloys are also available |
STAINLESS STEEL 316LN SQUARE TUBES INVENTORY:
- X = Stocked Item
- P = Call For availability square bar can be cut to size.
- Square bar can be polished per customer specifications.
- Square bar is stocked in Penn met 2000 for improved machinability.
| Size in Inches | Wt per Ft | Wt per 12′ | 303 | 304/L | 316/L | 416 |
|---|---|---|---|---|---|---|
| 3/16″ | 0.120 | 1.440 | X | X | X | P |
| 1/4″ | 0.210 | 2.52 | X | X | X | P |
| 5/16″ | 0.330 | 3.96 | X | X | X | X |
| 3/8″ | 0.480 | 5.76 | X | X | X | X |
| 7/16″ | 0.650 | 7.80 | X | X | X | X |
| 1/2″ | 0.850 | 10.20 | X | X | X | X |
| 9/16″ | 1.080 | 12.96 | X | X | X | X |
| 5/8″ | 1.330 | 15.96 | X | X | X | X |
| 3/4″ | 1.910 | 22.92 | X | X | X | X |
| 7/8″ | 2.610 | 31.32 | X | X | X | X |
| 1″ | 3.400 | 40.80 | X | X | X | X |
| 1-1/8″ | 4.310 | 51.72 | X | X | X | X |
| 1-1/4″ | 5.320 | 63.84 | X | X | X | X |
| 1-3/8″ | 6.400 | 76.80 | X | X | X | X |
| 1-1/2″ | 7.600 | 91.20 | X | X | X | X |
| 1-3/4″ | 10.400 | 124.80 | X | X | X | X |
| 2″ | 13.600 | 163.20 | X | X | X | X |
| 2-1/4″ | 17.200 | 206.40 | X | X | X | X |
| 2-1/2″ | 21.300 | 255.60 | X | X | X | X |
| 3″ | 30.63 | 367.56 | X | X | X | P |
| 4″ | 54.40 | 652.80 | X | X | X | P |
STAINLESS STEEL 316LN SQUARE TUBES PROCESSING:
Customers can select a number of processing options to produce stainless steel tubes to their exact specifications, reducing materiel costs, production time, scrap and internal handling.
| Long Product Processing Services Overview | |
|---|---|
| Square Tube Cutting | Products cut include Round Tube, Flat bar, Hex bar, Square bar, Tubing and Hollow Tube, Pipe, Angles, channels, Beams and Tees. Thickness range is 1/16″ to 28″ diameter |
| Square Tube Production Cutting | Penn Stainless can provide production cutting for product diameters up to 4″. We utilize Amanda Production Equipment to achieve these precision cuts with tight tolerances. |
| Square Tube Polishing | Products polished included all tubular products, with OD & ID polishing available, Round Tube, Square Tube, Hex & Flat bar, Angles, Uneven Leg Angles, beams, and other shapes. |
TOLERANCES FOR COLD AND HOT STAINLESS STEEL 316LN SQUARE TUBES:
COLD FINISHED STAINLESS STEEL 316LN SQUARE TUBES TOLERANCES:
| CF Tolerances | Plus | Minus |
|---|---|---|
| 1/8″ to 5/16″ (exclusive) | 0.000 | 0.002 |
| 5/16″ to 1/2″ (exclusive) | 0.000 | 0.003 |
| 1/2″ to 1″ (inclusive) | 0.000 | 0.004 |
| over 1″ to 2″ (inclusive) | 0.000 | 0.006 |
| over 2″ to 3″ (inclusive) | 0.000 | 0.008 |
COLD FINISHED STAINLESS STEEL 316LN SQUARE TUBES STRAIGHTNESS TOLERANCES:
CF: 1/16 inch in any 5 foot; but may not exceed 1/16 X (length in ft/5)
HOT FINISHED STAINLESS STEEL 316LN SQUARE TUBES TOLERANCES:
| HF Tolerances | Plus | Minus | Out of Sq |
|---|---|---|---|
| Over 7/8″ to 1″ (inclusive) | 0.009 | 0.009 | 0.013 |
| Over 1″ to 1-1/8″ (inclusive) | 0.010 | 0.010 | 0.015 |
| Over 1-1/8″ to 1-1/4″ (inclusive) | 0.011 | 0.011 | 0.016 |
| Over 1-1/4″ to 1-3/8″ (inclusive) | 0.012 | 0.012 | 0.018 |
| Over 1-3/8″ to 1-1/2″ (inclusive) | 0.014 | 0.014 | 0.021 |
| Over 1-1/2″ to 2″ (inclusive) | 1/64 | 1/64 | 0.023 |
HOT FINISHED STAINLESS STEEL 316LN SQUARE TUBES STRAIGHTNESS TOLERANCES:
HF: 1/8 inch in any 5 foot; but may not exceed 1/8 X (length in ft/5)
STAINLESS STEEL 316LN SQUARE TUBES SPECIFICATIONS:
| Stainless Steel Square Tube Specifications | |
|---|---|
| ASTM A276 | This specification encompasses cold-finished or hot-finished tubes, including rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. |
| ASTM A479 | This specification includes cold and hot finished stainless steel tubes, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels. |
| ASTM A484 | This specification includes wrought stainless steel tubes, shapes, forgings, and billets or other semi-finished materials, except wire, for forging. The materials are available in four types of conditions. |
| ASTM A582 | This specification includes cold or hot finished tubes, which are suitable for machining processes. This specification includes rounds, squares, and hexagons, from common types of stainless free-machining steels. |
| ASTM B473 | This specification includes nickel alloy bar & wire, which can be produced in a solution-annealed condition, stabilized-annealed condition, or annealed condition. |
We export our STAINLESS STEEL 316LN SQUARE TUBES products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at harshsteel@ymail.com for your instant requirements.
