ASTM A276 UNS S43000 Hex Bars, SS 420 Hexagon Bars, Stainless Steel 420 Round Bars Supplier, Manufacturer and Exporter in India
Din 1.4034 SS 430 Hexagon Bars, SS UNS S42000 Round Bars, Stainless Steel 420 Threaded Rods, 420 Stainless Steel Cold Drawn Bars Suppliers in India.
GENERAL PROPERTIES:-
Alloy 420 is a hardenable, martensitic stainless steel that is a modification of Alloy 410. Similar to 410, it contains a minimum of 12% chromium, just sufficient enough to give corrosion resistant properties. Alloy 420 has higher carbon content than Alloy 410 which is designed to optimize strength and hardness characteristics. It has good ductility it the annealed condition but is capable of being hardened up to Rockwell hardness 50 HRC, the highest hardness of the 12% chromium grades. Due to its hardening properties, Alloy 420 is not often welded, although it is possible. Martensitic stainless steels are designed for high hardness and sometimes other properties are to some degree compromised. Corrosion resistance is lower than the common austenitic grades and their useful operating range is limited by their loss of ductility at sub-zero temperatures and loss of strength by over-tempering at elevated temperatures. Its best corrosion resistance is achieved when the metal is hardened and surface ground or polished.
APPLICATIONS:-
Alloy 420 is used for a variety of applications where good corrosion and outstanding hardness is necessary. It is not usually used at temperatures exceeding 800oF (427oC) due to quick hardening and loss of corrosion resistance. Examples of applications that use alloy 420 include:
- Cuttery
- Knife blades
- Surgical instruments
- Needle valves
- Shear blades
- Scissors
- Hand tools
CORROSION RESISTANCE:
- Less resistant than the austenitic grades and the 17% chromium ferritic alloys
- Good resistance in the hardened condition to the atmosphere, foods, fresh water, and mild acids
- Resistance lowered in the annealed condition
- Best with a smooth surface finish
HEAT RESISTANCE:
- Not recommended for use above the relevant tempering temperature because of reduction in mechanical properties
- Scaling temperature is approximately 1202oF (650oC)
WELDING:
- Not commonly welded due to air hardening characteristics.
- Welding may be performed after preheating to 300-400 F
- Post weld tempering at temperature for 2 hours
HOT WORKING:
- Recommended to bring temperatures slowly up to 1400, then on to 2000-2200 F
- Furnace cool slowly to avoid cracking, after furnace working
- Reheating is necessary to keep working temperature above 1600 F.
COLD WORKING:
- Can withstand only minor cold work.
- Radical forming operations will result in cracking.
ANEALING:
- Anneal at temperatures between 1550-1650 F (843-900 C)
- Allow for slow furnace cooling.
TEMPERING:
- Temper at temperatures of 300-400 F
- Air cool for maximum hardness and corrosion resistance.
HARDENING:
- Soak at 1850-1950 F to quench in heated oil.
HEX BARS PRODUCT OVERVEIW
Stainless Steel Hex Bar | |
---|---|
Thickness Range of Flat Bar | 3/16″ thru 3″ Larger sizes available upon request |
Grades | 202, 304/304L, 316/316L,304H, 316H, 309/S, 310/S, 317/L, 321/H, 347/H, 904L, 330, 254SMO, 410. In duplex grades, we can supply 2205 and 2507. Some nickel Alloy such as alloy 200/201, C276, Alloy 400, Alloy 600, Alloy 625, Alloy 800H, Alloy 800HT, 254SMO, AL6XN and others Titanium alloys and copper alloys are also available |
INVENTORY:
Size in Inches | Wt per Ft | Wt per 12′ | 303 | 304/L | 316/L | 416 |
---|---|---|---|---|---|---|
3/16″ | 0.104 | 1.248 | X | X | X | X |
1/4″ | 0.180 | 2.160 | X | X | X | X |
5/16″ | 0.290 | 3.480 | X | X | X | X |
3/8″ | 0.410 | 4.920 | X | X | X | X |
7/16″ | 0.560 | 6.72 | X | X | X | X |
1/2″ | 0.740 | 8.880 | X | X | X | X |
9/16″ | 0.930 | 11.16 | X | X | X | X |
5/8″ | 1.150 | 13.80 | X | X | X | X |
11/16″ | 1.390 | 16.68 | X | X | X | |
3/4″ | 1.660 | 19.92 | X | X | X | X |
13/16″ | 1.950 | 23.40 | X | X | X | |
7/8″ | 2.300 | 27.60 | X | X | X | X |
15/16″ | 2.600 | 31.20 | X | X | X | X |
1″ | 2.90 | 34.80 | X | X | X | X |
1-1/16″ | 3.30 | 39.60 | X | X | X | X |
1-1/8″ | 3.700 | 44.40 | X | X | X | X |
1-1/4″ | 4.600 | 55.20 | X | X | X | X |
1-5/16″ | 5.100 | 61.20 | X | X | X | |
1-3/8″ | 5.600 | 67.20 | X | X | X | X |
1-7/16″ | 6.100 | 73.20 | X | X | X | |
1-1/2″ | 6.600 | 79.20 | X | X | X | X |
1-5/8″ | 7.800 | 93.60 | X | X | X | |
1-3/4″ | 9.030 | 108.36 | X | X | X | X |
1-7/8″ | 10.400 | 124.80 | X | X | X | X |
2″ | 11.80 | 141.60 | X | X | X | X |
2-1/4″ | 14.920 | 179.04 | X | X | X | X |
2-3/8″ | 16.920 | 203.04 | X | X | X | |
2-1/2″ | 18.42 | 221.04 | X | X | X | X |
3″ | 26.53 | 318.36 | X | X | X | X |
STAINLESS STEEL BAR VALUE ADDED OPTIONS:
Stainless Steel Bar Value Added Options | |
---|---|
Stainless Steel Bar Polishing | Harsh Steel can polish nearly any stainless steel bar item to a #4 polish, #6 Polish, #7 polish or a #8 mirror finish. Stainless steel polished bar can also be cut to size. Pitt free surfaces can also be provided. |
Heatreating & Annealing | Some grades of stainless steel bars can be heatreated to change the mechanical properties. Precipitation Hardening Stainless Steels such as 17-4PH can be heatreated. 410 stainless steel bar can also be heatreated. In some cases, secondary annealing 300 series stainless steel may be required depending on the application |
Positive Material Identification (PMI) | Harsh Steel can perform PMI testing in house for most stainless steel grades, or we can work with independent labs to complete PMI in order to meet customer specifications. |
UT Testing | In some cases, UT testing of the stainless steel bar may be required. We can assist you with this requirement. |
- Need 1,100 pieces of 7/8″ 303 round bar cut to 2-1/8″ long? We can process this job in a few days with our Amada CM100CNC with precise part tolerances
- Rapid cut of round bar 5/8″ thru 4″ dia
- Larger stainless bar cutting thru 26″ in diameter
- Multiple cutting stations allow us to ship cut stainless bar to size when you need it.
- Grinding and polishing available upon request
- Special heat treat requirements can also be supplied. Ask for details.
- Stainless round bars can also be polished or center-less ground to exact tolerances.
We export our STAINLESS STEEL 420 HEX BARS products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at harshsteel@ymail.com for your instant requirements.