UNS S43000 Hex Bars, SS 430 Hexagon Bars, Stainless Steel 430 Round Bars Supplier, Manufacturer and Exporter in India
Din 1.4016 SS 430 Hexagon Bars, SS UNS S43000 Round Bars, Stainless Steel 430 Threaded Rods, 440 Stainless Steel Cold Drawn Bars Suppliers in India.
GENERAL PROPERTIES:-
Grade 430 is a ferritic, straight chromium, non-hardenable grade, combining good corrosion resistance and formability characteristics with useful mechanical properties. Its ability to resist nitric acid attack permits its use in specific chemical applications but automotive trim and appliance components represents its largest fields of application.
Grade 430F is the free-machining version of this grade, available in bar form for use in automatic screw machines. Grade 434 is the molybdenum bearing version of Grade 430 and has the same useful combination of properties. Its molybdenum addition improves corrosion resistance.
These properties for 430 are specified for flat rolled product (plate, sheet and coil) in ASTM A240/A240M. Similar but not necessarily identical properties are specified for other products such as forgings and bar in their respective specifications. Properties of Grade 430F are specified for bar in ASTM A582.
APPLICATIONS:-
Typical applications for 430 grade include:
- Linings for dish washers
- Refrigerator cabinet panels
- Automotive trim
- Lashing Wire
- Element Supports
- Stove trim rings
- Fasteners
- Chimney Liners
Typical applications for 430F grade include:
- Repetition machined components
CORROSION RESISTANCE:-
Grade 430 has good resistance to a wide variety of corrosive enviornments, including nitric acid and some organic acids. It attains its maximum corrosion resistance when in the highly polished or buffed condition. In general its resistance to pitting and crevice corrosion resistance is close to that of grade 304. Stress corrosion cracking resistance of Grade 430 is very high, as it is for all ferritic grades.
Like other high-sulphur free machining grades 430F has much reduced resistance to pitting and crevice corrosion compared to its non-free machining equivalent.
HEAT TREATMENT:-
- Solution Annealing – Heat to 815-845°C, hold for ½ hour per 25mm of thickness, slow furnace cool to 600°C and then quickly air cool. Slow cooling from 540-400°C will cause embrittlement.
- Sub-Critical anneal – Heat to 760-815°C and then air cool or water quench.
- This grade is not hardenable by thermal treatment.
WELDING:-
- Pre-heat at 150-200°C if welding is necessary.
- Embrittlement in the weld metal and heat affected zone can be relieved by a post-weld anneal at 790-815°C
- Grain refinement will not occur.
MACHINING:-
- Easier to machine than the standard austenitic grades such as 304.
- Still a tendency for galling and pick-up on the cutting tool.
- Bars that have been lightly drawn are easier to machine than those in the annealed condition.
- Grade 430F, the free machining version of 430, is very much easier to machine.
FABRICATION:-
- Lower work hardening rate makes bending and forming somewhat easier than for grade 304
- Lower ductility restricts very severe operations.
- Severe bends should be made with the bend axis at right angles to the rolling direction.
- Severe cold heading of 430 wire is possible.
COMPOSITION:-
Grade | C | Mn | Si | P | S | Cr | Mo | Ni | N | |
---|---|---|---|---|---|---|---|---|---|---|
430 | min. max. | - 0.12 | - 1.00 | - 1.00 | - 0.040 | - 0.030 | 16.0 18.0 | - | - 0.75 | - |
430F | min. max. | - 0.12 | - 1.25 | - 1.00 | - 0.06 | 0.15- | 16.0 18.0 | - | - | - |
MECHANICAL PROPERTIES:-
Grade | Tensile Strength (MPa) min | Yield Strength 0.2% Proof (MPa) min | Elongation (% in 50mm) min | Hardness | |
---|---|---|---|---|---|
Rockwell B (HR B) max | Brinell (HB) max | ||||
430 | 450 | 205 | 22 | 89 | 183 |
430F | 552 typical | 379 typical | 25 typical | - | 262 |
PHYSICAL PROPERTIES:-
Grade | Density (kg/m3) | Elastic Modulus (GPa) | Mean Coefficient of Thermal Expansion (mm/m/°C) |
Thermal Conductivity (W/m.K) |
Specific Heat 0-100°C (J/kg.K) | Electrical Resistivity (nW.m) | |||
---|---|---|---|---|---|---|---|---|---|
0-100°C | 0-315°C | 0-538°C | at 100°C | at 500°C | |||||
430 | 7750 | 200 | 10.4 | 11.0 | 11.4 | 23.9 | 26.0 | 460 | 600 |
430F | 7750 | 200 | 10.4 | 11.0 | 11.4 | 26.1 | 26.3 | 460 | 600 |
POSSIBLE ALTERNATIVE GRADES:-
In the table below are a list of possible alternative grades to Grade 430.
Grade | Reason it may be chosen instead of 430 |
---|---|
430F | Higher machinability than 430 is needed in bar product, and reduced corrosion resistance is acceptable. |
434 | Better pitting resistance is required |
304 | Slightly higher corrosion resistance is needed, together with greatly improved ability to be welded and cold formed |
316 | Much better corrosion resistance is needed, together with greatly improved ability to be welded and cold formed |
3CR12 | A lower corrosion resistance is acceptable in a cost-critical application |
Stainless Steel Pipe Fittings and Flanges | |
Manufacture | Stainless steel Welded and Seamless pipe fittings |
Size Range | DN6 - DN600 |
Grades | 202, ASTM A312 in 304/304L and 316/316L,304H, 316H, 309/S, 310/S, 317/L, 321/H, 347/H, 904L, 330, 254SMO, 410. In duplex grades, we can supply 2205 and 2507. Some nickel Alloy such as alloy 200/201, C276, Alloy 400, Alloy 600, Alloy 625, Alloy 800H, Alloy 800HT, 254SMO, AL6XN and others Titanium alloys and copper alloys are also available |
---|---|
Wall Thickness | Sch 10S, 40S, 80S |
Type | Stainless steel Butt weld, Screwed & socket, Flanges |
Shapes | Stainless steel Elbows, Tees, Reducers, Caps, Stub ends, Flanges (ANSI, Table E & Table D) |
HEX BARS PRODUCT OVERVEIW
Stainless Steel Hex Bar | |
---|---|
Thickness Range of Flat Bar | 3/16″ thru 3″ Larger sizes available upon request |
Grades | 202, 304/304L, 316/316L,304H, 316H, 309/S, 310/S, 317/L, 321/H, 347/H, 904L, 330, 254SMO, 410. In duplex grades, we can supply 2205 and 2507. Some nickel Alloy such as alloy 200/201, C276, Alloy 400, Alloy 600, Alloy 625, Alloy 800H, Alloy 800HT, 254SMO, AL6XN and others Titanium alloys and copper alloys are also available |
INVENTORY:
Size in Inches | Wt per Ft | Wt per 12′ | 303 | 304/L | 316/L | 416 |
---|---|---|---|---|---|---|
3/16″ | 0.104 | 1.248 | X | X | X | X |
1/4″ | 0.180 | 2.160 | X | X | X | X |
5/16″ | 0.290 | 3.480 | X | X | X | X |
3/8″ | 0.410 | 4.920 | X | X | X | X |
7/16″ | 0.560 | 6.72 | X | X | X | X |
1/2″ | 0.740 | 8.880 | X | X | X | X |
9/16″ | 0.930 | 11.16 | X | X | X | X |
5/8″ | 1.150 | 13.80 | X | X | X | X |
11/16″ | 1.390 | 16.68 | X | X | X | |
3/4″ | 1.660 | 19.92 | X | X | X | X |
13/16″ | 1.950 | 23.40 | X | X | X | |
7/8″ | 2.300 | 27.60 | X | X | X | X |
15/16″ | 2.600 | 31.20 | X | X | X | X |
1″ | 2.90 | 34.80 | X | X | X | X |
1-1/16″ | 3.30 | 39.60 | X | X | X | X |
1-1/8″ | 3.700 | 44.40 | X | X | X | X |
1-1/4″ | 4.600 | 55.20 | X | X | X | X |
1-5/16″ | 5.100 | 61.20 | X | X | X | |
1-3/8″ | 5.600 | 67.20 | X | X | X | X |
1-7/16″ | 6.100 | 73.20 | X | X | X | |
1-1/2″ | 6.600 | 79.20 | X | X | X | X |
1-5/8″ | 7.800 | 93.60 | X | X | X | |
1-3/4″ | 9.030 | 108.36 | X | X | X | X |
1-7/8″ | 10.400 | 124.80 | X | X | X | X |
2″ | 11.80 | 141.60 | X | X | X | X |
2-1/4″ | 14.920 | 179.04 | X | X | X | X |
2-3/8″ | 16.920 | 203.04 | X | X | X | |
2-1/2″ | 18.42 | 221.04 | X | X | X | X |
3″ | 26.53 | 318.36 | X | X | X | X |
STAINLESS STEEL BAR VALUE ADDED OPTIONS:
Stainless Steel Bar Value Added Options | |
---|---|
Stainless Steel Bar Polishing | Harsh Steel can polish nearly any stainless steel bar item to a #4 polish, #6 Polish, #7 polish or a #8 mirror finish. Stainless steel polished bar can also be cut to size. Pitt free surfaces can also be provided. |
Heatreating & Annealing | Some grades of stainless steel bars can be heatreated to change the mechanical properties. Precipitation Hardening Stainless Steels such as 17-4PH can be heatreated. 410 stainless steel bar can also be heatreated. In some cases, secondary annealing 300 series stainless steel may be required depending on the application |
Positive Material Identification (PMI) | Harsh Steel can perform PMI testing in house for most stainless steel grades, or we can work with independent labs to complete PMI in order to meet customer specifications. |
UT Testing | In some cases, UT testing of the stainless steel bar may be required. We can assist you with this requirement. |
- Need 1,100 pieces of 7/8″ 303 round bar cut to 2-1/8″ long? We can process this job in a few days with our Amada CM100CNC with precise part tolerances
- Rapid cut of round bar 5/8″ thru 4″ dia
- Larger stainless bar cutting thru 26″ in diameter
- Multiple cutting stations allow us to ship cut stainless bar to size when you need it.
- Grinding and polishing available upon request
- Special heat treat requirements can also be supplied. Ask for details.
- Stainless round bars can also be polished or center-less ground to exact tolerances.
We export our STAINLESS STEEL 430 HEX BARS products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at harshsteel@ymail.com for your instant requirements.