Duplex Steel 2205 Flanges, UNS s31803 Flanges Supplier & Exporter

GENERAL PROPERTIES:

Duplex 2205 is a two-phase, ferritic, austenitic 22% chromium, 3% molybdenum, 5 to 6% nickel alloyed stainless steel. It is the most widely used duplex stainless steel grade and is characterized by high yield strength, double that of the standard austenitic stainless steel grades. It also demonstrates good fatigue strength, as well as outstanding resistance to stress corrosion cracking, crevice, pitting, erosion, and general corrosion in severe environments.

APPLICATION:

• Chemical processing, transport and storage – pressure vessels, tanks, piping, and heat exchangers
• Oil and gas exploration and processing equipment – piping, tubing, and heat exchangers
• Marine and other high chloride environments
• Effluent scrubbing systems
• Pulp and paper industry – digesters, bleaching equipment, and stock-handling systems
• Cargo tanks for ships and trucks
• Food processing equipment
• Biofuels plants

COROSSION RESISTANCE:

• Due to its high chromium, molybdenum, and nitrogen content, Duplex 2205 demonstrates superior corrosion resistant properties to 316 and 316L in most environments
• Chromium, molybdenum, and nitrogen content also provide high resistance to pitting and crevice corrosion, even in oxidizing and acidic solutions
• Resistant to chloride stress corrosion cracking and temperatures of up to about 302°F (150°C)
• The presence of ferrite provides for good performance of Duplex 2205 in caustic environments

HEAT RESISTANCE:

• Similar to other duplex stainless steels, Duplex 2205 has good oxidation resistance at high temperatures
• Subject to embrittlement when exposed to temperatures above 572°F (300°C) even when exposed for short periods of time; Duplex 2205 is therefore not recommended for use above 572°F (300°C)

WELDING CHARACTERISTICS:

• Possesses good weldability
• Should not generally be welded without filler metal as this may result in excessive ferrite

HEAT TREATMENT:

• Annealing temperature range is 1868 to 2012°F (1020 to 1100°C)
• Cannot be hardened by heat treatment – but Duplex 2205 does work-harden
• Special consideration is needed to compensate for a higher coefficient of thermal expansion to avoid warping and distortion

PROCESSING - HOT FORMING:

Most Duplex 2205 producers recommend a maximum hot forming temperature between 2010 and 2100°F (1100 to 1150°C). If the shape of the work piece is not compact, the edges may be significantly cooler than the bulk, and there is risk of cracking in the cooler regions.

PROCESSING - COLD FORMING:

Duplex 2205 has shown good formability in a variety of fabrications. The high strength of Duplex 2205 can pose problems. Even when the equipment has sufficient power, allowance must be made for higher spring-back caused by the grade's high strength.

MACHINABILITY:

Duplex 2205 is somewhat more difficult to machine than the 300 series austenitic stainless steels. Higher cutting forces are required and more rapid tool wear is typical. Some guidelines for machining are: A) Use powerful, rigid machines with extremely strong rigid mounting of tools and work piece, B) Minimize vibration by keeping the tool extension as short as possible, C) Use a nose radius on the tool, no longer than necessary, for carbides that have a sharp edge while still providing adequate strength, D) Design machining sequences to always provide for a depth of cut below the work hardened layer resulting from the previous passes.

CHEMICAL PROPERTIES:

	C	Mn	Si	P	S	Cr	Mo	Ni	N
2205 (S31803)	0.03 max	2.0 max	1.0 max	0.03 max	0.02 max	min: 21.0 max: 23.0	min: 2.5 max: 3.5	min: 4.5 max: 6.5	min: 0.08 max: 0.20
2205 (S32205)	0.03 max	2.0 max	1.0 max	0.03 max	0.02 max	min: 22.0 max: 23.0	min: 3.0 max: 3.5	min: 4.5 max: 6.5	min: 0.14 max: 0.20

MECHANICAL PROPERTIES:

Grade	Tensile Strength ksi (min)	Yield Strength 0.2% ksi (min)	Elongation %	Hardness (HB) MAX
2205	90	65	25	217

PHYSICAL PROPERTIES:

	Density lbm/in3	Electrical Resistivity mW•in	Thermal Conductivity (BTU/hr•ft•°F)	Heat Capacity BTU/lbm•°F	Electrical Resistivity (in x 10-6)
at 68°F	0.278	27.6	8.7	0.112	33.5
at 212°F		26.1	9.2	0.119	35.4
at 392°F		25.4	9.8	0.127	37.4
at 572°F		24.9	10.4	0.134	39.4

TYPES AND SPECIFICATIONS:

ASME/ANSI B16.5	Welding Neck Flange, Slipon Flange, Blind Flange, High Hub Blind Flange, Socket Weld Flange, Lap Joint Flange, Threaded Flange, Ring Type Joint Flange
Pressure Class	150, 300, 400, 600, 900, 1500, 2500
ASME/ANSI B16.47	Welding Neck Flange, Blind Flange (Series A & B)
Pressure Class	75, 150, 300, 400, 600, 900
ASME/ANSI B 16.36	(Orifice Flanges) Welding Neck Flange, Slipon Flange, Threaded Flange
Pressure Class	300, 400, 600, 900, 1500, 2500
BS 4504 SEC 3.1	Welding Flange (111/134), Hubbed Slipon Flange (112), Hubbed Threaded Flange (113), Lapped Pipe End Flange (133), Plate Flange (101), Loose Plate Flange (102), Loose Plate with Weld-neck Flange (104), Blank Flange (105)
Pressure Class	PN 2.5 to PN 100
Din Flanges	DIN2527, DIN2566, DIN2573, DIN2576, DIN2641, DIN2642, DIN2655, DIN2656, DIN2627, DIN2628, DIN2629, DIN2631, DIN2632, DIN2633, DIN2634, DIN2635, DIN2636, DIN2637, DIN2638, DIN2673
Pressure Class	PN 6 to PN 100
ANFOr NFE 29-230	Plate Flange (01), loose Plate Flange (02, 03, 04), Blind Flange (05), Welding Neck flange (11), Hubbed Slip on Flange (12), Screwed Flange (13),Hubbed Socket Welding Flange (14), Loose Hubbed Flange (15) Integral Flange (21)
Pressure Class	Iso - PN 2.5 to PN 40
Pr EN 1092-1 Flanges	Plate Flange (01), Loose Plate Flange (02, 04), Blind Flange (05), Welding Neck Flange (11), Hubbed Slip on flange (12), Screwed Flange (13), Integral Flange (21)
Pressure Class	PN 2.5 to PN 100
ASME/ANSI B 16.9/MSS SP-4	Stub End
Type	A, B, C

Metal	Grade	UNS Number
Austenitic / Ferritic / Austenitic / Stainless Steel	F304 / F304H / F304L * F309* F310* / F310H* F316 / F316H / F316L* F317 / F317L* F321 / F321H* F347 / F347H* F51 (2205)* / F60* F53 (2507)* F446*	S30400 / S30409 / S30403 S30900 S31000 / S31009 S31600 / S31609 / S31603 S31700 / S31703 S32100 / S32109 S34700 / S34709 S31803 / S32205 S32750 S44600
Ferritic / Martensitic Alloys	F1* F5 / F5 A* F6 CL 1, 2, 3, 4, (F410)* F9* F11 CL 1, 2, 3* F22 CL 1, 3* F91* F12 CL 2*	K12822 K41545 / K42544 S41000 K90941 K11597 / K11572 K21590 K90901 K11564
Nickel & Nickel Based Alloys	Nickel 200* Nickel 201* Alloy 400* Alloy 600* Alloy 601 Alloy 625 Alloy 800 / 800H / 800HT* Alloy 825* Alloy 904L* Alloy 20* Alloy C276*	N02200 N02201 N04400 N06600 N06601 N06625 N08800 / N08810 / N08811 N08825 N08904 N08020 N10276
Low Temperature Alloys	LF - 1* LF - 2* LF - 3* A707 L3* A694 F42 - F65* A350 LF6*	K03009 K03011 K32025
Aluminum Alloys	Alum 3003* Alum 6061	A93003 A96061
Copper - Nickel Alloys	70/30 90/10	C71500 C70600

GRADES

ASTM	304/304L/304H, 316/316L/316H, 317/317L, 321/321H, 347/347H, 316Ti, F51
DIN	WNR 1.4541, WNR 1.4571, WNR 1.4301, WNR 1.4306, WNR 1.4307, WNR 1.4401, WNR 1.4404, WNR 1.4438, WNR 1.4462
AFNOR (NF E)	BF Z 3 CN 19-09, BF Z 7 CN 18-09, BF Z 6 CNT 18-10, BF Z 3 CND 17-11-02, BF Z 7 CND 17-11-02, BF Z 6 CNDT 17-12, BF Z 6 CNDNb 18-12

STAINLESS STEEL FLANGES

A wide variety of stainless steel flanges are all available at CCTF, including weld necks, slip-ons, threaded, socket weld, lap joints, blinds, and hub blinds.

GRADES A316/316L and A304/304L

---

---

---

---

---

---

---

Enquiry

---