UNS S31600 Flanges, SS 316 Flanges, AISI SS 316 Stainless Steel 316 Flanges Supplier, Manufacturer and Exporter in India
Din 1.4401 SS 316 Flanges, SS UNS S31600 Flanges, Stainless Steel 316 Flanges, 316 Stainless Steel 316 Flanges Suppliers in India.
GENERAL PROPERTIES
Alloy 316/316L is molybdenum-bearing austenitic stainless steel. The higher nickel and molybdenum content in this grade allows it to demonstrate better overall corrosion resistant properties than 304, especially with regard to pitting and crevice corrosion in chloride environments. In addition, Alloy 316/ 316L provides excellent elevated temperature tensile, creep and stress-rupture strengths, as well as outstanding formability and weldability. 316L is the lower carbon version of 316 and is immune from sensitization; therefore, it is very frequently used in heavy gauge welded components.
APPLICATIONS
- Food preparation equipment, especially in chloride environments
- Chemical processing, equipment
- Laboratory benches and equipment
- Rubber, plastics, pulp & paper machinery
- Pollution control equipment
- Boat fittings, value and pump trim
- Heat exchangers
- Pharmaceutical and textile industries
- Condensers, evaporators and tanks
CORROSION RESISTANCE
- Generally more resistant than 304 in range of atmospheric environments and many corrosive media due to the increased chromium
and molybdenum content. - Subject to pitting and crevice corrosion in warm chloride environments, and to stress corrosion cracking above about 122°F (50°C).
- Considered resistant to potable water with up to about 1000mg/L chlorides at ambient temperatures, reducing to about 500mg/L at
140°F (60°C). - Usually regarded as the "marine grade stainless steel" – but is not resistant to warm sea water.
HEAT RESISTANCE
- Good oxidation resistance in intermittent service to 1600°F (870°C) and in continuous service to 1700°F (925°C)
- Grade 316L is more resistant to carbide precipitation.
WELDING CHARACTERISTICS
- Excellent weldability by all standard fusion methods, both with and without filler metals.
- Heavy welded sections in Grade 316 require post-weld annealing for maximum corrosion resistance, this is not required for grade 316L.
HEAT TREATMENT
- Annealing temperature range is 1900 to 2100°F (1038 to 1149°C).
- Cannot be hardened by heat treatment.
- Special consideration is needed to compensate for a higher coefficient of thermal expansion to avoid warping and distortion.
PROCESSING - HOT FORMING
- Most producers recommend a maximum forging temperature between 2100°F and 2300°F
- Do not forge below 1700°F (927°C) Best
- Corrosion resistance is obtained if the forgings are given a final anneal.
PROCESSING - COLD FORMING
- 316/316L types being extremely tough and ductile, can be readily cold worked such as roll form, swaging, cold heading, deep drawing,
bent, etc., without difficulty - Severely cold formed parts should be annealed to remove stresses.
MACHINEABILITY
- Type 316/316L is somewhat more difficult to machine than Type 304 because of its toughness.
- 316/316L machines with chip characteristics that are tough and strong.
- Chip breakers and curlers are advised.
- As large a tool as possible and great amounts of cutting fluid should be used.
- Heavy positive feeds at low speeds should be considered since 316/316L work hardens rapidly.
CHEMICAL PROPERTIES:
C | Mn | Si | P | S | Cr | Mo | Ni | N | |
---|---|---|---|---|---|---|---|---|---|
316 (S31600) |
0.08 max |
2.0 max |
0.75 max |
0.045 max |
0.03 max |
min: 16.0 max: 18.0 |
min: 2.0 max: 3.0 |
min: 10.0 max: 14.0 |
0.10 max |
316L (S31603) |
0.03 max |
2.0 max |
0.75 max |
0.045 max |
0.03 max |
min: 16.0 max: 18.0 |
min: 2.0 max: 3.0 |
min: 10.0 max: 14.0 |
0.10 max |
MECHANICAL PROPERTIES:
Grade | Tensile Strength ksi (min) |
Yield Strength 0.2% ksi (min) |
Elongation % | Hardness (Brinell) MAX | Hardness (Rockwell B) MAX |
---|---|---|---|---|---|
316 (S31600) |
75 | 30 | 40 | 217 | 95 |
316L (S31603) |
70 | 25 | 40 | 217 | 95 |
PHYSICAL PROPERTIES:
Density lbm/in3 |
Thermal Conductivity (BTU/h ft. °F) |
Electrical Resistivity (in x 10-6) |
Modulus of Elasticity (psi x 106 |
Coefficient of Thermal Expansion (in/in)/°F x 10-6 |
Specific Heat (BTU/lb/°F) |
Melting Range (°F) |
---|---|---|---|---|---|---|
0.29 at 68°F | 100.8 at 68 212°F | 29.1 at 68°F | 29 | 8.9 at 32 – 212°F | 0.108 at 68°F | 2500 to 2550 |
9.7 at 32 – 1000°F | 0.116 at 200°F | |||||
11.1 at 32 – 1500°F |
ASME/ANSI B16.5 | Welding Neck Flange, Slipon Flange, Blind Flange, High Hub Blind Flange, Socket Weld Flange, Lap Joint Flange, Threaded Flange, Ring Type Joint Flange |
---|---|
Pressure Class | 150, 300, 400, 600, 900, 1500, 2500 |
ASME/ANSI B16.47 | Welding Neck Flange, Blind Flange (Series A & B) |
Pressure Class | 75, 150, 300, 400, 600, 900 |
ASME/ANSI B 16.36 | (Orifice Flanges) Welding Neck Flange, Slipon Flange, Threaded Flange |
Pressure Class | 300, 400, 600, 900, 1500, 2500 |
BS 4504 SEC 3.1 | Welding Flange (111/134), Hubbed Slipon Flange (112), Hubbed Threaded Flange (113), Lapped Pipe End Flange (133), Plate Flange (101), Loose Plate Flange (102), Loose Plate with Weld-neck Flange (104), Blank Flange (105) |
Pressure Class | PN 2.5 to PN 100 |
Din Flanges | DIN2527, DIN2566, DIN2573, DIN2576, DIN2641, DIN2642, DIN2655, DIN2656, DIN2627, DIN2628, DIN2629, DIN2631, DIN2632, DIN2633, DIN2634, DIN2635, DIN2636, DIN2637, DIN2638, DIN2673 |
Pressure Class | PN 6 to PN 100 |
ANFOr NFE 29-230 | Plate Flange (01), loose Plate Flange (02, 03, 04), Blind Flange (05), Welding Neck flange (11), Hubbed Slip on Flange (12), Screwed Flange (13),Hubbed Socket Welding Flange (14), Loose Hubbed Flange (15) Integral Flange (21) |
Pressure Class | Iso - PN 2.5 to PN 40 |
Pr EN 1092-1 Flanges | Plate Flange (01), Loose Plate Flange (02, 04), Blind Flange (05), Welding Neck Flange (11), Hubbed Slip on flange (12), Screwed Flange (13), Integral Flange (21) |
Pressure Class | PN 2.5 to PN 100 |
ASME/ANSI B 16.9/MSS SP-4 | Stub End |
Type | A, B, C |
Metal | Grade | UNS Number |
---|---|---|
Austenitic / Ferritic / Austenitic / Stainless Steel | F304 / F304H / F304L * F309* F310* / F310H* F316 / F316H / F316L* F317 / F317L* F321 / F321H* F347 / F347H* F51 (2205)* / F60* F53 (2507)* F446* |
S30400 / S30409 / S30403 S30900 S31000 / S31009 S31600 / S31609 / S31603 S31700 / S31703 S32100 / S32109 S34700 / S34709 S31803 / S32205 S32750 S44600 |
Ferritic / Martensitic Alloys | F1* F5 / F5 A* F6 CL 1, 2, 3, 4, (F410)* F9* F11 CL 1, 2, 3* F22 CL 1, 3* F91* F12 CL 2* |
K12822 K41545 / K42544 S41000 K90941 K11597 / K11572 K21590 K90901 K11564 |
Nickel & Nickel Based Alloys | Nickel 200* Nickel 201* Alloy 400* Alloy 600* Alloy 601 Alloy 625 Alloy 800 / 800H / 800HT* Alloy 825* Alloy 904L* Alloy 20* Alloy C276* |
N02200 N02201 N04400 N06600 N06601 N06625 N08800 / N08810 / N08811 N08825 N08904 N08020 N10276 |
Low Temperature Alloys | LF - 1* LF - 2* LF - 3* A707 L3* A694 F42 - F65* A350 LF6* |
K03009 K03011 K32025 |
Aluminum Alloys | Alum 3003*
Alum 6061 |
A93003
A96061 |
Copper - Nickel Alloys | 70/30 90/10 |
C71500 C70600 |
ASTM | 304/304L/304H, 316/316L/316H, 317/317L, 321/321H, 347/347H, 316Ti, F51 |
---|---|
DIN | WNR 1.4541, WNR 1.4571, WNR 1.4301, WNR 1.4306, WNR 1.4307, WNR 1.4401, WNR 1.4404, WNR 1.4438, WNR 1.4462 |
AFNOR (NF E) | BF Z 3 CN 19-09, BF Z 7 CN 18-09, BF Z 6 CNT 18-10, BF Z 3 CND 17-11-02, BF Z 7 CND 17-11-02, BF Z 6 CNDT 17-12, BF Z 6 CNDNb 18-12 |
STAINLESS STEEL FLANGES
A wide variety of stainless steel flanges are all available at CCTF, including weld necks, slip-ons, threaded, socket weld, lap joints, blinds, and hub blinds.
GRADES A316/316L and A304/304L
- Weld Neck
- Sch10, Sch40 and Sch80 Bore
- Classes 150, 300, 600, 900, 1500
- Sizes: ½" to 24"
- Slip-On
- Classes 150, 300, 600, 900, 1500
- Sizes: ½" to 24"
- Threaded
- Classes 150 & 300
- Sizes: ½" to 4"
- Lap Joint
- Class 150 only
- Sizes: 2" to 6"
- Blind
- Classes 150 & 300
- Sizes: ½" to 12"
- Hub Blind
- Classes 300, 600, 1500
- Sizes: ½" to 6"
- Socket Weld
- Sch40 & Sch80 Bore
- Classes 150, 300, 600
- Sizes: ½" to 2"
We export our STAINLESS STEEL 316 FLANGES products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at harshsteel@ymail.com for your instant requirements.