UNS S44000 Flanges, SS 440 Flanges, Stainless Steel 440 Flanges Supplier, Manufacturer and Exporter in India
Din 1.4125 SS 440 Flanges, SS UNS S44000 Flanges, Stainless Steel 440 Flanges, 440 Stainless Steel Flanges Suppliers in India.
GENERAL PROPERTIES:-
Stainless steels are high-alloy steels which have high corrosion resistance compared to other steels due to the presence of large amounts of chromium. Based on their crystalline structure, they are divided into three types such as ferritic, austenitic, and martensitic steels. Another group of stainless steels are precipitation-hardened steels. They are a combination of martensitic and austenitic steels. Grade 440C stainless steel is a high carbon martensitic stainless steel. It has high strength, moderate corrosion resistance, and good hardness and wear resistance. Grade 440C is capable of attaining, after heat treatment, the highest strength, hardness and wear resistance of all the stainless alloys. Its very high carbon content is responsible for these characteristics, which make 440C particularly suited to such applications as ball bearings and valve parts.
APPLICATIONS:-
Typical applications include:
- Rolling element bearings
- Valve seats
- High quality knife blades
- Surgical instruments
- Chisels
CORROSION RESISTANCE:-
Good resistance to the atmosphere, fresh water, foods, alkalies and mild acids. Best resistance in the hardened and tempered and passivated condition. A smooth polished surface also assists.
The corrosion resistance of grade 440C approximates that of grade 304 in many environments.
HEAT RESISTANCE:-
Not recommended for use in temperatures above the relevant tempering temperature, because of reduction in mechanical properties by over-tempering.
HEAT TREATMENT:-
Annealing – Full anneal – 850-900°C, slow furnace cool to about 600°C and then air cool. Sub-critical Annealing – 735-785°C and slow furnace cool.
Hardening – Heat to 1010-1065°C, followed by quenching in warm oil or air. Oil quenching is necessary for heavy sections. Immediately temper at 150-370°C to obtain a wide variety of hardness values and mechanical properties as indicated in the accompanying table.
Tempering in the range 425-565°C is to be avoided because of reduced impact resistance and corrosion resistance. Tempering in the range 590-675°C results in lower hardness (the product become machinable) and high impact resistance.
WELDING:-
If welding is necessary pre-heat at 250°C and follow welding with a full anneal. Grade 420 filler will give a high hardness weld (although not as high as the 440C), but 309 or 310 will produce soft welds with higher ductility.
MACHINING:-
In the annealed condition this grade is relatively easily machined; approximately the same as for high speed steel. Chips are tough and stringy so chip breakers are important. If these grades are hardened machining becomes more difficult and probably impossible.
COMPOSITION:-
Grade | C | Mn | Si | P | S | Cr | Mo | Ni | N | |
---|---|---|---|---|---|---|---|---|---|---|
440C | min. max. | 0.95 1.20 | - 1.00 | - 1.00 | - 0.040 | - 0.030 | 16.00 18.00 | - 0.75 | - | - |
MECHANICAL PROPERTIES:-
Tempering Temperature (°C) | Tensile Strength (MPa) | Yield Strength 0.2% Proof (MPa) | Elongation (% in 50mm) | Hardness Rockwell (HR C) | Impact Charpy V (J) |
---|---|---|---|---|---|
Annealed* | 758 | 448 | 14 | 269HB max# | - |
204 | 2030 | 1900 | 4 | 59 | 9 |
260 | 1960 | 1830 | 4 | 57 | 9 |
316 | 1860 | 1740 | 4 | 56 | 9 |
371 | 1790 | 1660 | 4 | 56 | 9 |
* Annealed properties are typical for Condition A of ASTM A276# Brinell Hardness is ASTM A276 specified maximum for annealed 440A, B and C. |
PHYSICAL PROPERTIES:-
Grade | Density (kg/m3) | Elastic Modulus (GPa) | Mean Coefficient of Thermal Expansion (mm/m/°C) | Thermal Conductivity(W/m.K) |
Specific Heat 0-100°C (J/kg.K) |
Electrical Resistivity (nW.m) | |||
---|---|---|---|---|---|---|---|---|---|
0-100°C | 0-200°C | 0-600°C | at 100°C | at 500°C | |||||
440 C | 7650 | 200 | 10.1 | 10.3 | 11.7 | 24.2 | - | 460 | 600 |
POSSIBLE ALTERNATIVE GRADES:-
Grade | Why it might be chosen instead of 440C |
---|---|
440A/B | Slightly softer and more corrosion resistant grade needed |
440F | High machinability required, with same hardness and hardenability as 440C |
420 | Lower strength and hardness needed than any of the 440 Grades |
416 | Higher machinability required, and the much lower hardness and strength is still adequate |
ASME/ANSI B16.5 | Welding Neck Flange, Slipon Flange, Blind Flange, High Hub Blind Flange, Socket Weld Flange, Lap Joint Flange, Threaded Flange, Ring Type Joint Flange |
---|---|
Pressure Class | 150, 300, 400, 600, 900, 1500, 2500 |
ASME/ANSI B16.47 | Welding Neck Flange, Blind Flange (Series A & B) |
Pressure Class | 75, 150, 300, 400, 600, 900 |
ASME/ANSI B 16.36 | (Orifice Flanges) Welding Neck Flange, Slipon Flange, Threaded Flange |
Pressure Class | 300, 400, 600, 900, 1500, 2500 |
BS 4504 SEC 3.1 | Welding Flange (111/134), Hubbed Slipon Flange (112), Hubbed Threaded Flange (113), Lapped Pipe End Flange (133), Plate Flange (101), Loose Plate Flange (102), Loose Plate with Weld-neck Flange (104), Blank Flange (105) |
Pressure Class | PN 2.5 to PN 100 |
Din Flanges | DIN2527, DIN2566, DIN2573, DIN2576, DIN2641, DIN2642, DIN2655, DIN2656, DIN2627, DIN2628, DIN2629, DIN2631, DIN2632, DIN2633, DIN2634, DIN2635, DIN2636, DIN2637, DIN2638, DIN2673 |
Pressure Class | PN 6 to PN 100 |
ANFOr NFE 29-230 | Plate Flange (01), loose Plate Flange (02, 03, 04), Blind Flange (05), Welding Neck flange (11), Hubbed Slip on Flange (12), Screwed Flange (13),Hubbed Socket Welding Flange (14), Loose Hubbed Flange (15) Integral Flange (21) |
Pressure Class | Iso - PN 2.5 to PN 40 |
Pr EN 1092-1 Flanges | Plate Flange (01), Loose Plate Flange (02, 04), Blind Flange (05), Welding Neck Flange (11), Hubbed Slip on flange (12), Screwed Flange (13), Integral Flange (21) |
Pressure Class | PN 2.5 to PN 100 |
ASME/ANSI B 16.9/MSS SP-4 | Stub End |
Type | A, B, C |
Metal | Grade | UNS Number |
---|---|---|
Austenitic / Ferritic / Austenitic / Stainless Steel | F304 / F304H / F304L * F309* F310* / F310H* F316 / F316H / F316L* F317 / F317L* F321 / F321H* F347 / F347H* F51 (2205)* / F60* F53 (2507)* F446* |
S30400 / S30409 / S30403 S30900 S31000 / S31009 S31600 / S31609 / S31603 S31700 / S31703 S32100 / S32109 S34700 / S34709 S31803 / S32205 S32750 S44600 |
Ferritic / Martensitic Alloys | F1* F5 / F5 A* F6 CL 1, 2, 3, 4, (F410)* F9* F11 CL 1, 2, 3* F22 CL 1, 3* F91* F12 CL 2* |
K12822 K41545 / K42544 S41000 K90941 K11597 / K11572 K21590 K90901 K11564 |
Nickel & Nickel Based Alloys | Nickel 200* Nickel 201* Alloy 400* Alloy 600* Alloy 601 Alloy 625 Alloy 800 / 800H / 800HT* Alloy 825* Alloy 904L* Alloy 20* Alloy C276* |
N02200 N02201 N04400 N06600 N06601 N06625 N08800 / N08810 / N08811 N08825 N08904 N08020 N10276 |
Low Temperature Alloys | LF - 1* LF - 2* LF - 3* A707 L3* A694 F42 - F65* A350 LF6* |
K03009 K03011 K32025 |
Aluminum Alloys | Alum 3003*
Alum 6061 |
A93003
A96061 |
Copper - Nickel Alloys | 70/30 90/10 |
C71500 C70600 |
ASTM | 304/304L/304H, 316/316L/316H, 317/317L, 321/321H, 347/347H, 316Ti, F51 |
---|---|
DIN | WNR 1.4541, WNR 1.4571, WNR 1.4301, WNR 1.4306, WNR 1.4307, WNR 1.4401, WNR 1.4404, WNR 1.4438, WNR 1.4462 |
AFNOR (NF E) | BF Z 3 CN 19-09, BF Z 7 CN 18-09, BF Z 6 CNT 18-10, BF Z 3 CND 17-11-02, BF Z 7 CND 17-11-02, BF Z 6 CNDT 17-12, BF Z 6 CNDNb 18-12 |
STAINLESS STEEL FLANGES
A wide variety of stainless steel flanges are all available at CCTF, including weld necks, slip-ons, threaded, socket weld, lap joints, blinds, and hub blinds.
GRADES A316/316L and A304/304L
- Weld Neck
- Sch10, Sch40 and Sch80 Bore
- Classes 150, 300, 600, 900, 1500
- Sizes: ½" to 24"
- Slip-On
- Classes 150, 300, 600, 900, 1500
- Sizes: ½" to 24"
- Threaded
- Classes 150 & 300
- Sizes: ½" to 4"
- Lap Joint
- Class 150 only
- Sizes: 2" to 6"
- Blind
- Classes 150 & 300
- Sizes: ½" to 12"
- Hub Blind
- Classes 300, 600, 1500
- Sizes: ½" to 6"
- Socket Weld
- Sch40 & Sch80 Bore
- Classes 150, 300, 600
- Sizes: ½" to 2"
We export our STAINLESS STEEL 440 FLANGES products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at harshsteel@ymail.com for your instant requirements.