Leading Provider of

Stainless Steel

Opening Times

Mon - Sat: 7.00 - 18:00

Get in touch

enquiry@harshsteel.com

UNS S31653 Square Bars, SS 316LN Square Bars, AISI SS 316LN Stainless Steel 316LN Square Bars Supplier, Manufacturer and Exporter in India


Din 1.4429 SS 316LN Square Bars, SS UNS S31653 Square Bars, Stainless Steel 316LN Square Bars, 316LN Stainless Steel 316LN Square Bars Suppliers in India.

INTRODUCTION:-

Stainless steel grade 316LN is an austenitic type of steel that is a low carbon, nitrogen-enhanced version of grade 316 steel. The nitrogen content in this steel provides solid solution hardening, and raises its minimum specified yield strength. It also possesses good resistance to general corrosion and pitting/crevice corrosion.


The following datasheet provides an overview of stainless steel grade 316LN.

CHEMICAL COMPOSITION:-

The chemical composition of grade 316LN stainless steel is outlined in the following table.

Element Content (%)
Iron, Fe Balance
Chromium, Cr 16.0-18.0
Nickel, Ni 10.0-14.0
Molybdenum, Mo 2.0-3.0
Manganese, Mn 2.00
Silicon, Si 1.00
Nitrogen, N 0.10-0.30
Phosphorous, P 0.045
Carbon, C 0.03
Sulphur, S 0.03

MECHANICAL PROPERTIES:-

The mechanical properties of grade 316LN stainless steel are displayed in the following table.

Properties Metric Imperial
Tensile strength 515 MPa 74694 psi
Yield strength 205 MPa 29732 psi
Modulus of elasticity 190-210 GPa 27557-30457 ksi
Poisson's ratio 0.27-0.30 0.27-0.30
Elongation at break (in 50 mm) 60% 60%

OTHER DESIGNATION:-

Equivalent materials to grade 316LN stainless steel are given below.

ASTM A182 ASTM A213 ASTM A240 ASTM A240 ASTM A276
ASTM A193 (B8MN, B8MNA) ASTM A312 ASTM A336 ASTM A358 ASTM A376
ASTM A194 (B8MN, B8MNA) ASTM A403 ASTM A430 ASTM A479 ASTM A666
ASTM A688

ASTM A813

ASTM A814

DIN 1.4406

DIN 1.4429

APPLICATION:-

Grade 316LN stainless steel is widely used in the following applications:

  • Trauma nails
  • Orthopedic implants
  • Neurological applications
  • Surgical instruments

SQUARE BAR PRODUCT OVERVIEW:-

Stainless Steel Square Bar
Thickness Range of Stainless Plate 3/16″ THRU 4″ (LARGER SIZES AVAILABLE UPON REQUEST)
Grades 202, 304/304L, 316/316L,304H, 316H, 309/S, 310/S, 317/L, 321/H, 347/H, 904L, 330, 254SMO, 410. In duplex grades, we can supply 2205 and 2507. Some nickel Alloy such as alloy 200/201, C276, Alloy 400, Alloy 600, Alloy 625, Alloy 800H, Alloy 800HT, 254SMO, AL6XN and others Titanium alloys and copper alloys are also available

INVENTORY:-

  • X = Stocked Item
  • P = Call For availability square bar can be cut to size.
  • Square bar can be polished per customer specifications.
  • Square bar is stocked in Penn met 2000 for improved machinability.
Size in Inches Wt per Ft Wt per 12′ 303 304/L 316/L 416
3/16″ 0.120 1.440 X X X P
1/4″ 0.210 2.52 X X X P
5/16″ 0.330 3.96 X X X X
3/8″ 0.480 5.76 X X X X
7/16″ 0.650 7.80 X X X X
1/2″ 0.850 10.20 X X X X
9/16″ 1.080 12.96 X X X X
5/8″ 1.330 15.96 X X X X
3/4″ 1.910 22.92 X X X X
7/8″ 2.610 31.32 X X X X
1″ 3.400 40.80 X X X X
1-1/8″ 4.310 51.72 X X X X
1-1/4″ 5.320 63.84 X X X X
1-3/8″ 6.400 76.80 X X X X
1-1/2″ 7.600 91.20 X X X X
1-3/4″ 10.400 124.80 X X X X
2″ 13.600 163.20 X X X X
2-1/4″ 17.200 206.40 X X X X
2-1/2″ 21.300 255.60 X X X X
3″ 30.63 367.56 X X X P
4″ 54.40 652.80 X X X P

PROCESSING:-

Customers can select a number of processing options to produce stainless steel bars to their exact specifications, reducing materiel costs, production time, scrap and internal handling.

Long Product Processing Services Overview
Square Bar Cutting Products cut include Round Bar, Flat bar, Hex bar, Square bar, Tubing and Hollow Bar, Pipe, Angles, channels, Beams and Tees.  Thickness range is 1/16″ to 28″ diameter
Square Bar Production Cutting Penn Stainless can provide production cutting for product diameters up to 4″.  We utilize Amanda Production Equipment to achieve these precision cuts with tight tolerances.
Square Bar Polishing Products polished included all tubular products, with OD & ID polishing available, Round Bar, Square Bar, Hex & Flat bar, Angles, Uneven Leg Angles, beams, and other shapes.

TOLERANCES FOR COLD AND HOT SQUARE BARS

COLD FINISHED SQUARE BAR TOLERANCES:

CF Tolerances Plus Minus
1/8″ to 5/16″ (exclusive) 0.000 0.002
5/16″ to 1/2″ (exclusive) 0.000 0.003
1/2″ to 1″ (inclusive) 0.000 0.004
over 1″ to 2″ (inclusive) 0.000 0.006
over 2″ to 3″ (inclusive) 0.000 0.008

COLD FINISHED SQUARE BAR STRAIGHTNESS TOLERANCES:

CF: 1/16 inch in any 5 foot; but may not exceed 1/16 X (length in ft/5)


HOT FINISHED SQUARE BAR TOLERANCES:

HF Tolerances Plus Minus Out of Sq
Over 7/8″ to 1″ (inclusive) 0.009 0.009 0.013
Over 1″ to 1-1/8″ (inclusive) 0.010 0.010 0.015
Over 1-1/8″ to 1-1/4″ (inclusive) 0.011 0.011 0.016
Over 1-1/4″ to 1-3/8″ (inclusive) 0.012 0.012 0.018
Over 1-3/8″ to 1-1/2″ (inclusive) 0.014 0.014 0.021
Over 1-1/2″ to 2″ (inclusive) 1/64 1/64 0.023

HOT FINISHED SQUARE BAR STRAIGHTNESS TOLERANCES:

HF: 1/8 inch in any 5 foot; but may not exceed 1/8 X (length in ft/5)


STAINLESS STEEL SQUARE BAR SPECIFICATIONS:

Stainless Steel Square Bar Specifications
ASTM A276 This specification encompasses cold-finished or hot-finished bars, including rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels.
ASTM A479 This specification includes cold and hot finished stainless steel bars, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels.
ASTM A484 This specification includes wrought stainless steel bars, shapes, forgings, and billets or other semi-finished materials, except wire, for forging. The materials are available in four types of conditions.
ASTM A582  This specification includes cold or hot finished bars, which are suitable for machining processes. This specification includes rounds, squares, and hexagons, from common types of stainless free-machining steels.
ASTM B473  This specification includes nickel alloy bar & wire, which can be produced in a solution-annealed condition, stabilized-annealed condition, or annealed condition.

We export our STAINLESS STEEL 316LN SQUARE BARS products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at harshsteel@ymail.com for your instant requirements.



Enquiry







OUR SUMMARY:
Reviewer :
Harsh steel
Review Date :
Reviewed Product :
STAINLESS STEEL 316LN SQUARE BARS
Author Rating
5starstarstarstarstar