Leading Provider of

Stainless Steel

Opening Times

Mon - Sat: 7.00 - 18:00

Get in touch

enquiry@harshsteel.com

ASTM A276 UNS S43000 Square Bars, SS 420 Square Bars, Stainless Steel 420 Square Bars Supplier, Manufacturer and Exporter in India


Din 1.4034 SS 430 Square Bars, SS UNS S42000 Square Bars, Stainless Steel 420 Square Rods, 420 Stainless Steel Square Bars Suppliers in India.

GENERAL PROPERTIES:-

Alloy 420 is a hardenable, martensitic stainless steel that is a modification of Alloy 410. Similar to 410, it contains a minimum of 12% chromium, just sufficient enough to give corrosion resistant properties. Alloy 420 has higher carbon content than Alloy 410 which is designed to optimize strength and hardness characteristics. It has good ductility it the annealed condition but is capable of being hardened up to Rockwell hardness 50 HRC, the highest hardness of the 12% chromium grades. Due to its hardening properties, Alloy 420 is not often welded, although it is possible. Martensitic stainless steels are designed for high hardness and sometimes other properties are to some degree compromised. Corrosion resistance is lower than the common austenitic grades and their useful operating range is limited by their loss of ductility at sub-zero temperatures and loss of strength by over-tempering at elevated temperatures. Its best corrosion resistance is achieved when the metal is hardened and surface ground or polished.

APPLICATIONS:-

Alloy 420 is used for a variety of applications where good corrosion and outstanding hardness is necessary. It is not usually used at temperatures exceeding 800oF (427oC) due to quick hardening and loss of corrosion resistance. Examples of applications that use alloy 420 include:

  • Cuttery
  • Knife blades
  • Surgical instruments
  • Needle valves
  • Shear blades
  • Scissors
  • Hand tools

CORROSION RESISTANCE:

  • Less resistant than the austenitic grades and the 17% chromium ferritic alloys
  • Good resistance in the hardened condition to the atmosphere, foods, fresh water, and mild acids
  • Resistance lowered in the annealed condition
  • Best with a smooth surface finish

HEAT RESISTANCE:

  • Not recommended for use above the relevant tempering temperature because of reduction in mechanical properties
  • Scaling temperature is approximately 1202oF (650oC)

WELDING:

  • Not commonly welded due to air hardening characteristics.
  • Welding may be performed after preheating to 300-400 F
  • Post weld tempering at temperature for 2 hours

HOT WORKING:

  • Recommended to bring temperatures slowly up to 1400, then on to 2000-2200 F
  • Furnace cool slowly to avoid cracking, after furnace working
  • Reheating is necessary to keep working temperature above 1600 F.

COLD WORKING:

  • Can withstand only minor cold work.
  • Radical forming operations will result in cracking.

ANEALING:

  • Anneal at temperatures between 1550-1650 F (843-900 C)
  • Allow for slow furnace cooling.

TEMPERING:

  • Temper at temperatures of 300-400 F
  • Air cool for maximum hardness and corrosion resistance.

HARDENING:

  • Soak at 1850-1950 F to quench in heated oil.

SQUARE BAR PRODUCT OVERVIEW:-

Stainless Steel Square Bar
Thickness Range of Stainless Plate 3/16″ THRU 4″ (LARGER SIZES AVAILABLE UPON REQUEST)
Grades 202, 304/304L, 316/316L,304H, 316H, 309/S, 310/S, 317/L, 321/H, 347/H, 904L, 330, 254SMO, 410. In duplex grades, we can supply 2205 and 2507. Some nickel Alloy such as alloy 200/201, C276, Alloy 400, Alloy 600, Alloy 625, Alloy 800H, Alloy 800HT, 254SMO, AL6XN and others Titanium alloys and copper alloys are also available

INVENTORY:-

  • X = Stocked Item
  • P = Call For availability square bar can be cut to size.
  • Square bar can be polished per customer specifications.
  • Square bar is stocked in Penn met 2000 for improved machinability.
Size in Inches Wt per Ft Wt per 12′ 303 304/L 316/L 416
3/16″ 0.120 1.440 X X X P
1/4″ 0.210 2.52 X X X P
5/16″ 0.330 3.96 X X X X
3/8″ 0.480 5.76 X X X X
7/16″ 0.650 7.80 X X X X
1/2″ 0.850 10.20 X X X X
9/16″ 1.080 12.96 X X X X
5/8″ 1.330 15.96 X X X X
3/4″ 1.910 22.92 X X X X
7/8″ 2.610 31.32 X X X X
1″ 3.400 40.80 X X X X
1-1/8″ 4.310 51.72 X X X X
1-1/4″ 5.320 63.84 X X X X
1-3/8″ 6.400 76.80 X X X X
1-1/2″ 7.600 91.20 X X X X
1-3/4″ 10.400 124.80 X X X X
2″ 13.600 163.20 X X X X
2-1/4″ 17.200 206.40 X X X X
2-1/2″ 21.300 255.60 X X X X
3″ 30.63 367.56 X X X P
4″ 54.40 652.80 X X X P

PROCESSING:-

Customers can select a number of processing options to produce stainless steel bars to their exact specifications, reducing materiel costs, production time, scrap and internal handling.

Long Product Processing Services Overview
Square Bar Cutting Products cut include Round Bar, Flat bar, Hex bar, Square bar, Tubing and Hollow Bar, Pipe, Angles, channels, Beams and Tees.  Thickness range is 1/16″ to 28″ diameter
Square Bar Production Cutting Penn Stainless can provide production cutting for product diameters up to 4″.  We utilize Amanda Production Equipment to achieve these precision cuts with tight tolerances.
Square Bar Polishing Products polished included all tubular products, with OD & ID polishing available, Round Bar, Square Bar, Hex & Flat bar, Angles, Uneven Leg Angles, beams, and other shapes.

TOLERANCES FOR COLD AND HOT SQUARE BARS

COLD FINISHED SQUARE BAR TOLERANCES:

CF Tolerances Plus Minus
1/8″ to 5/16″ (exclusive) 0.000 0.002
5/16″ to 1/2″ (exclusive) 0.000 0.003
1/2″ to 1″ (inclusive) 0.000 0.004
over 1″ to 2″ (inclusive) 0.000 0.006
over 2″ to 3″ (inclusive) 0.000 0.008

COLD FINISHED SQUARE BAR STRAIGHTNESS TOLERANCES:

CF: 1/16 inch in any 5 foot; but may not exceed 1/16 X (length in ft/5)


HOT FINISHED SQUARE BAR TOLERANCES:

HF Tolerances Plus Minus Out of Sq
Over 7/8″ to 1″ (inclusive) 0.009 0.009 0.013
Over 1″ to 1-1/8″ (inclusive) 0.010 0.010 0.015
Over 1-1/8″ to 1-1/4″ (inclusive) 0.011 0.011 0.016
Over 1-1/4″ to 1-3/8″ (inclusive) 0.012 0.012 0.018
Over 1-3/8″ to 1-1/2″ (inclusive) 0.014 0.014 0.021
Over 1-1/2″ to 2″ (inclusive) 1/64 1/64 0.023

HOT FINISHED SQUARE BAR STRAIGHTNESS TOLERANCES:

HF: 1/8 inch in any 5 foot; but may not exceed 1/8 X (length in ft/5)


STAINLESS STEEL SQUARE BAR SPECIFICATIONS:

Stainless Steel Square Bar Specifications
ASTM A276 This specification encompasses cold-finished or hot-finished bars, including rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels.
ASTM A479 This specification includes cold and hot finished stainless steel bars, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels.
ASTM A484 This specification includes wrought stainless steel bars, shapes, forgings, and billets or other semi-finished materials, except wire, for forging. The materials are available in four types of conditions.
ASTM A582  This specification includes cold or hot finished bars, which are suitable for machining processes. This specification includes rounds, squares, and hexagons, from common types of stainless free-machining steels.
ASTM B473  This specification includes nickel alloy bar & wire, which can be produced in a solution-annealed condition, stabilized-annealed condition, or annealed condition.

We export our STAINLESS STEEL 420 SQUARE BARS products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at harshsteel@ymail.com for your instant requirements.




Enquiry







OUR SUMMARY:
Reviewer :
Harsh steel
Review Date :
Reviewed Product :
STAINLESS STEEL 420 SQUARE BARS
Author Rating
5starstarstarstarstar