UNS S31700 Square Bars, SS 317 Square Bars, AISI SS 317 Stainless Steel 317 Square Bars Supplier, Manufacturer and Exporter in India
Din 1.4449 SS 317 Square Bars, SS UNS S31700 Square Bars, Stainless Steel 317 Square Bars, 317 Stainless Steel 317 Square Bars Suppliers in India.
GENERAL PROPERTIES:-
317L is a molybdenum bearing, low carbon content "L" grade austenitic stainless steel that provides improved corrosion resistance over 304L and 316L stainless steels. The low carbon provides resistance to sensitization during welding and other thermal processes.
317L is non-magnetic in the annealed condition but may become slightly magnetic as a result of welding.
APPLICATIONS:-
Flue-gas desulfurization systems
Chemical process vessels
Petrochemical
Pulp and Paper
Condensers in power generation
CORROSION PROPERTIES:-
317L has excellent corrosion resistance in a wide range of chemicals, especially in acidic chloride environments such as those encountered in pulp and paper mills. Increased levels of chromium, nickel and molybdenum compared to 316L stainless steel improve resistance to chloride pitting and general corrosion. Resistance increases with molybdenum alloy content. 317L is resistant to sulfuric acid concentrations up to 5 percent at temperatures as high as 120°F (49°C). At temperatures under 100°F (38°C) this alloy has excellent resistance to solutions of higher concentration. However, service tests are recommended to account for the affects of specific operating conditions that may affect corrosion behavior. In processes where condensation of sulfur-bearing gases occurs, 317L is much more resistant to attack at the point of condensation than conventional alloy 316. The acid concentration has a marked influence on the rate of attack in such environments and should be carefully determined by service tests.
WELDING:-
317L is readily welded by a full range of conventional welding procedures (except oxyacetylene). AWS E317L/ER317L filler metal or austenitic, low carbon filler metals with molybdenum content higher than that of 317L, or a nickel-base filler metal with sufficient chromium and molybdenum content to exceed the corrosion resistance of 317L should be used to weld 317L steel.
CHARACTERISTICS:-
Improved general and localized corrosion to 316L stainless
Good formability
Good weldability
CHEMICAL PROPERTIES:-
Ni
Cr
Mo
Mn
Si
11.0 - 15.0
18.0 - 20.0
3.0 - 4.0
2.0 Max
.75 Max
C
N
S
P
Fe
0.03 Max
0.1 Max
0.03 Max
0.045 Max
Balance
MECHANICAL PROPERTIES:-
Ultimate Tensile Strength, ksi Minimum
.2% Yield Strength, ksi Minimum
Elongation Percent
Hardness Max.
75
30
35
217 Brinell
SQUARE BAR PRODUCT OVERVIEW:-
Stainless Steel Square Bar
Thickness Range of Stainless Plate
3/16″ THRU 4″ (LARGER SIZES AVAILABLE UPON REQUEST)
Grades
202, 304/304L, 316/316L,304H, 316H, 309/S, 310/S, 317/L, 321/H, 347/H, 904L, 330, 254SMO, 410. In duplex grades, we can supply 2205 and 2507. Some nickel Alloy such as alloy 200/201, C276, Alloy 400, Alloy 600, Alloy 625, Alloy 800H, Alloy 800HT, 254SMO, AL6XN and others Titanium alloys and copper alloys are also available
INVENTORY:-
X = Stocked Item
P = Call For availability square bar can be cut to size.
Square bar can be polished per customer specifications.
Square bar is stocked in Penn met 2000 for improved machinability.
Size in Inches
Wt per Ft
Wt per 12′
303
304/L
316/L
416
3/16″
0.120
1.440
X
X
X
P
1/4″
0.210
2.52
X
X
X
P
5/16″
0.330
3.96
X
X
X
X
3/8″
0.480
5.76
X
X
X
X
7/16″
0.650
7.80
X
X
X
X
1/2″
0.850
10.20
X
X
X
X
9/16″
1.080
12.96
X
X
X
X
5/8″
1.330
15.96
X
X
X
X
3/4″
1.910
22.92
X
X
X
X
7/8″
2.610
31.32
X
X
X
X
1″
3.400
40.80
X
X
X
X
1-1/8″
4.310
51.72
X
X
X
X
1-1/4″
5.320
63.84
X
X
X
X
1-3/8″
6.400
76.80
X
X
X
X
1-1/2″
7.600
91.20
X
X
X
X
1-3/4″
10.400
124.80
X
X
X
X
2″
13.600
163.20
X
X
X
X
2-1/4″
17.200
206.40
X
X
X
X
2-1/2″
21.300
255.60
X
X
X
X
3″
30.63
367.56
X
X
X
P
4″
54.40
652.80
X
X
X
P
PROCESSING:-
Customers can select a number of processing options to produce stainless steel bars to their exact specifications, reducing materiel costs, production time, scrap and internal handling.
Long Product Processing Services Overview
Square Bar Cutting
Products cut include Round Bar, Flat bar, Hex bar, Square bar, Tubing and Hollow Bar, Pipe, Angles, channels, Beams and Tees. Thickness range is 1/16″ to 28″ diameter
Square Bar Production Cutting
Penn Stainless can provide production cutting for product diameters up to 4″. We utilize Amanda Production Equipment to achieve these precision cuts with tight tolerances.
Square Bar Polishing
Products polished included all tubular products, with OD & ID polishing available, Round Bar, Square Bar, Hex & Flat bar, Angles, Uneven Leg Angles, beams, and other shapes.
TOLERANCES FOR COLD AND HOT SQUARE BARS
COLD FINISHED SQUARE BAR TOLERANCES:
CF Tolerances
Plus
Minus
1/8″ to 5/16″ (exclusive)
0.000
0.002
5/16″ to 1/2″ (exclusive)
0.000
0.003
1/2″ to 1″ (inclusive)
0.000
0.004
over 1″ to 2″ (inclusive)
0.000
0.006
over 2″ to 3″ (inclusive)
0.000
0.008
COLD FINISHED SQUARE BAR STRAIGHTNESS TOLERANCES:
CF: 1/16 inch in any 5 foot; but may not exceed 1/16 X (length in ft/5)
HOT FINISHED SQUARE BAR TOLERANCES:
HF Tolerances
Plus
Minus
Out of Sq
Over 7/8″ to 1″ (inclusive)
0.009
0.009
0.013
Over 1″ to 1-1/8″ (inclusive)
0.010
0.010
0.015
Over 1-1/8″ to 1-1/4″ (inclusive)
0.011
0.011
0.016
Over 1-1/4″ to 1-3/8″ (inclusive)
0.012
0.012
0.018
Over 1-3/8″ to 1-1/2″ (inclusive)
0.014
0.014
0.021
Over 1-1/2″ to 2″ (inclusive)
1/64
1/64
0.023
HOT FINISHED SQUARE BAR STRAIGHTNESS TOLERANCES:
HF: 1/8 inch in any 5 foot; but may not exceed 1/8 X (length in ft/5)
STAINLESS STEEL SQUARE BAR SPECIFICATIONS:
Stainless Steel Square Bar Specifications
ASTM A276
This specification encompasses cold-finished or hot-finished bars, including rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels.
ASTM A479
This specification includes cold and hot finished stainless steel bars, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels.
ASTM A484
This specification includes wrought stainless steel bars, shapes, forgings, and billets or other semi-finished materials, except wire, for forging. The materials are available in four types of conditions.
ASTM A582
This specification includes cold or hot finished bars, which are suitable for machining processes. This specification includes rounds, squares, and hexagons, from common types of stainless free-machining steels.
ASTM B473
This specification includes nickel alloy bar & wire, which can be produced in a solution-annealed condition, stabilized-annealed condition, or annealed condition.
We export our STAINLESS STEEL 317 SQUARE BARS products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at
harshsteel@ymail.com for your instant requirements.